Err

Same day shipping / Next day delivery
The UK's home of peelable, sprayable paint since 2012

METALLIC - ORANGE

FullDip Matte Metallic Orange (shown).

ALL colours are MATTE as standard.

FullDip Metallic Orange (shown).

PLUS gloss topcoat (FullDip PRO Gloss shown).

Metallic Orange is a fairly popular colour. Scroll down to see all Metallic Orange items. Click BUY to buy an item, or click on the picture to get more information about the product.

INFO

Metallic Orange is a FullDip colour. It is available in the FullDip range and PlastiDip range.

We recommend using the grey primer base.

This will give a matte finish.

You can topcoat it with satin or glossifier to alter the finish. Or our PRO gloss & matte finishes to add fuel resistance.
The aerosols are metallic already, but for the 4 litres you will need to add the 'Metallic Maker' tinter (see bottom).

** Be careful with the metallic maker on this colour **

** Mix it a little at a time. Too much metallic and you can make the colour very pale, almost a silvery colour **

*** We recommend using this in a satin / gloss topcoat. To make the metallic flake really pop and visible ***


APPLICATION

2 light dust coats of spraywrap primer grey.

2-3 wet coats primer grey.

Then at least 3 or 4 full wet coats of the Metallic Orange  


EQUIPMENT

Earlex HV2901, MS3000, FullDip FD650 or usual compressor setup 1.7-2.0 tip at 20-28 PSI and the TSS ProHSE.

Remember on compressors, the higher the PSI, the more you waste as it floats away in the air. Yes it will be smooth, but difficult to peel as most will be on the floor. So try to go as low as possible. We find great results vs waste at about 25 PSI.


Aerosols

Self explanetory, shake and spray.

This is a FullDip colour and available in FullDip aerosols.

Plastidip® aeros 100% need warming. We also recommend you do with the FullDip aerosols too.

https://youtu.be/6Mmo3-DNPCc

Its a good habit to get into with ANY aerosol. tbh


Sprayable

This is a FullDip colour, can also be made into a PlastiDip sprayable.
To make this metallic add the 'Metallic Maker' tinter (see bottom).


Tinters / Drop-Ins

No measuring needed, simply pour the contents of the tinter into a CLEAR FullDip 4 litre, 1 US Gallon of CLEAR PDS or a 5 litre PlastiDip CLEAR mix.

Then add the 'Metallic Maker' at the bottom. If you do not add the metallic maker, it will be a solid colour. You can adjust the metallic effect by adding a little of it at a time and mixing. It is quite strong, and on lighter colours we recommend not using the smallest amount. You can turn the red for instance a little pinker because it also lightens it.

Make sure shake well and you get ALL the colourant out. Sometimes pigment settles and clumps at the bottom

You can add to another colour, but they are designed for a CLEAR

Instructions and video here;

https://www.facebook.com/mattpackltd/videos/1349095861790721/

https://www.facebook.com/mattpackltd/videos/1145169222183387/


Wheel Kits

Will give you the base colour and colour to acheive the requested (shown above) colour.

Come in a matte or gloss finish

See our wheel kit explanation HERE

These kits will usually do upto a set of 19" front faces perfectly.


Starter Kits

Order the correct kit in these stages;

Decide the size needed (email us) B, C or D.

Choose the gun.

Choose the finish.



FullDip®

Wheel Kits

Wheel kits upto 19" (front face) you would require

2x primer base and 3x Metallic Orange 

To make glossy add 1-2 of these;

Rememeber to leave the above dip 24 hours to cure properly!

Starter Kits

SIZE B

1 x Grey Primer and 1 x CLEAR 4L and 1 x Tinter and 1 x Metallic Maker Tinter

SIZE C

1 x Grey Primer and 2 x CLEAR 4L and 2 x Tinter and 2 x Metallic Maker Tinter

SIZE D

2 x Grey Primer and 2 x CLEAR 4L and 2 x Tinter and 2 x Metallic Maker Tinter

Then choose your gun if you need one;

FullDip FD650 Turbine Sprayer
£ 99.99
(-10.00%) £ 89.99
Shopping Satisfaction
(1)
TSS ProHse
£ 360.50

ALL dip is matte finish, if you want to make shiny, add some of these as a topcoat

A or B use 1

C or D use 2

For a Satin finish, use the kits below. Full instructions and use in the product description

Or for a PRO, fuel resistant topcoat (requires professional compressor setup and professional equipment)

NOT compatible with turbine setups.

NOT designed as a DIY product.

A & B use 1

C use 1.5

D use 2