Err

Same day shipping / Next day delivery
The UK home of Peelable Paint & spray wraps
PlastiDip Pearl Pearlizer Matte Aerosol
  • PlastiDip Pearl Pearlizer Matte Aerosol
  • PlastiDip Pearl Pearlizer Matte Aerosol
  • PlastiDip Pearl Pearlizer Matte Aerosol
  • PlastiDip Pearl Pearlizer Matte Aerosol

PlastiDip Pearl Pearlizer Matte Aerosol

PLASTI DIP
(Code: pdaeroprprl)
In Stock

311gr / 400ml Aerosol
Matte finish
Recommended BASE : BLACK

£ 9.46(10.60 €)
500g
Genuine USA Made 311gr (400ml) Plasti Dip® Pearl Pearlizer Aerosol

Please note this colour is effect only, it is not a colour. It is designed to go over solid colours to give a 'white' pearl effect. It looks great in the sun light, and really gives you that edge.

We are an authorised PLASTI DIP® RE-Seller. The longest running and biggest independent PLASTI DIP® seller in the UK. 


How To Spray:

Spraying (aerosol)

1. Surface must be clean and dry. For best results, avoid direct sunlight, high humidity, or breezy conditions.

2. Shake can vigorously for one full minute after mixing ball begins to rattle. Shake often while applying.

3. Hold can 6-10” from surface, moving can back and forth, slightly overlapping each stroke. Apply heavily enough to produce an even, wet appearance.

4. Allow 30 minutes’ minimum between coats. Apply as many coats as desired (3-4 average).

5. Allow 4 hours’ minimum dry time before use. Coverage: Approximately 5-10 sq. ft. per can. 


Spraying Tips:

Always protect surrounding areas from over spray. Allow 4 hours per coat for complete dry. If runs or sags are experienced, move can further away from surface. To avoid clogged nozzle, turn can upside down and spray for 5 seconds. If clogged, remove nozzle and soak in naphtha or mineral spirits for 30 minutes. Do not stick pin or other objects into stem. Use naphtha, xylene (xylol), or toluene (toluol) for clean-up. To greatly increase non-skid properties, sprinkle a generous amount of grit onto wet surface of first coat. Apply at least two additional coats of Plasti Dip. For best results, use a pumice (crystalline silica) grit. Results may vary with other grit additives. When applied properly PLASTI DIP can be removed from most surfaces, if desired.


** Information taken directly from PLASTI DIP in USA**

 Read the complete MSDS information on PLASTI DIP and PLASTI DIP Spray.


For best results;

  • Boil a kettle
  • Pour into a jug
  • Sit the can in the jug for a few minutes to warm it up
  • Dry can and shake well
  • Use as described leaving 10 mins between coats, 5 coats is best.
  • Leave overnight to dry and cure

DIY Synthetic Rubber Coating

Plasti Dip is a multi-purpose, air dry, specialty rubber coating. It can be easily applied by dipping, brushing, or spraying. Plasti Dip protective coating is ideal for a broad array of do-it-yourself projects around the home, garage, garden, and elsewhere. It protects coated items against moisture, acids, abrasion, corrosion, and skidding/slipping, and provides a comfortable, controlled grip. Plasti Dip remains flexible and stretchy over time, and will not crack or become brittle in extreme weather conditions. It has been tested and proven in temperatures from -30°F to 200°F.

Using Plasti Dip Spray in cooler temperatures may affect drying times, finish quality, and spray performance. If you plan on spraying your project in cooler conditions, we recommend pre-warming the aerosol can by placing it in a warm room and allowing the contents to reach room temperature. Under no circumstances should users subject the aerosol can to temperatures above 120°F or use heat from an open flame or other sources of ignition to pre-warm the spray can. Additionally, cooler conditions may affect the surface you are spraying. If you are concerned about spraying your project in cooler temperatures, test in an inconspicuous area first to ensure the resulting finish will be what you’re looking for.

 



Fully Auth Distributor

Secure Payments

Shipping Information